Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
Just how do you feel about How to Install a Bathtub?
Installing a bath tub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably hard project. If the old bathtub is readily easily accessible, the project can move speedily; if you need to open a wall surface to remove the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as set in the brand-new one. See to it you have actually certified yourself for the work as well as are comfortable trying it. Rather than employing a specialist to take over a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you install a new tub in your washroom if you have already acquired a brand-new tub and also do not need to change the plan of your previous water pipes.
Your tools as well as product list need to consist of the following:
Planning for the Installation
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be quite bothersome as a result of the limited gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before going on to fit the brand-new taps, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed position. The wooden boards are practical in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the bath tub up until the level reviews degree.
To set up taps, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water supply and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the tub as well as also examine the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub needs to wait until the bath tub has been used at least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Safeguard the tap in place with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous type must be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall between the bathroom as well as the tiling, resulting in difficulties with moisture as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture rather early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that entry on How to Install a Bathtub when doing a lookup on the web. Are you aware of another individual who is very much interested in the topic? Please feel free to promote it. Thank you so much for going through it.
Premium service for plumbing emergencies. Report this page